|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
1.25mm Pitch Super Low profile Crimping Connector DF14 Series sFeatures 1. Super Low Profile This is a connector special for right angle which has pursued a low profile on the board. Board mounting height: 2.5mm A signal can be fetched from the area where there is no board to board space. Board Mounting Figure 2. Correspond to Automatic Mounting The header has the vacuum mount face which enables the vacuum absorption and the automatic mounting by the embossed tape packaging.In addition, the tube packaging can be selected. 3. Four Wall Type Without Friction to Board by Socket The header has the box structure to prevent from being twisted and has the perfect mis-insertion prevention method. Moreover the header has the wall on the board side and doesn't have any trouble resulted from the friction to board by socket. In addition, the metal fitting is attached to prevent the solder peel. 1 sApplications LCD, Note PC, Mobile Terminal Small business equipment, Video camera B177 sProduct Specifications Rating Item 1. Insulation Resistance 2. Withstanding voltage 3. Contact Resistance 5. Vibration 500M ohms Min No flashover or insulation breakdown. 30m ohms Max No electrical discontinuity of 1s or more Current rating 1A Operating Temperature Range-25 to +85c (Note 1) 40 to 80% Storage Temperature Range -10 to +60c (Note 2) Storage Moisture Range Condition 100V DC 500V AC/1 minute 100mA Measure at the square steel pin of 0.30.002mm Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 96 hours at temperature of 40c and humidity of 90% to 95% (-25c: 30 minutes5 to 35c: 10 minutes85c: 30 minutes 5 to 35c: 10 minutes) 5 cycles Tin plating: 30 cycles Gold plating: 50 cycles Reflow: At the recommended temperature profile Manual soldering: 300c for 3 seconds 40 to 70% Voltage rating 150V AC Operating Moisture Range Specification 4. Insertion/Extraction Force MIN0.15N (15gf), MAX3N (300gf) 6. Humidity (Steady state) Contact resistance: 30m ohms Max Insulation resistance:500M ohms Min 7. Temperature Cycle Contact resistance: 30m ohms Max Insulation resistance: 500M ohms Min 8. Durability (Mating/un-mating) Contact resistance: 30m ohms Max 9. Resistance to Soldering heat No deformation of components affecting performance. Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. sMaterial Product Crimping Socket Crimping Contact for Socket Pin Header Part Insulator Contact Insulator Contact Fitting Material Polyamide Phosphor Copper Polyamide Brass Phosphor copper Finish Beige Tin-lead plated or gold plated Beige Tin-lead plated or gold plated Tin-lead plated Remarks UL-94V-0 ------- UL-94V-0 ------- ------- Note . Hirose's tin plating product takes measures against whisker. sOrdering Information qConnector DF14 1 1 2 3 Series Name: DF14 - * S - 1.25 C 2 3 4 5 4 5 Contact Pitch: 1.25mm Contact Type C: Crimping socket H: Right angle SMT Number of Contacts: 2 to 10, 15, 20, 25, 30 Connector Type S: Single row socket P: Single row pin header qContact DF14 - 2628 SCF A 1 1 Applicable cable size 2628: AWG26 to 28 3032: AWG30 to 32 2 2 3 3 Packaging Type SCF: Socket contact/reel Plating Type Blank: Tin plated A: Gold plated B178 sCrimping Socket Photo: Contact insertion state Unit: mm Part Number DF14- 2S-1.25C(**) DF14- 3S-1.25C(**) DF14- 4S-1.25C(**) DF14- 5S-1.25C(**) DF14- 6S-1.25C(**) DF14- 7S-1.25C(**) DF14- 8S-1.25C(**) DF14- 9S-1.25C(**) DF14-10S-1.25C(**) DF14-15S-1.25C(**) DF14-20S-1.25C(**) DF14-25S-1.25C(**) DF14-30S-1.25C(**) CL No. 538-0005-8-** 538-0006-0-** 538-0007-3-** 538-0008-6-** 538-0009-9-** 538-0010-8-** 538-0011-0-** 538-0013-6-** 538-0014-9-** 538-0054-3-** 538-0059-7-** 538-0064-7-** 538-0012-3-** Number of Contacts 2 3 4 5 6 7 8 9 10 15 20 25 30 A 4.45 5.70 6.95 8.20 9.45 10.70 11.95 13.20 14.45 20.70 26.95 33.20 39.45 B 1.25 2.50 3.75 5.00 6.25 7.50 8.75 10.00 11.25 17.50 23.75 30.00 36.25 [Specific No.]-**,(**) Blank : 1 bag 100 pcs. Note 1.The quantity at the specific No. "Blank" is delivered per bag. If needed, please order the products per bag. sSocket Crimping Contact Part Number DF14-2628SCF DF14-3032SCF CL No. 538-0001-7-** 538-0003-2-** Packaging Type Reel Reel Quantity 10,000 Finish Tin plated KApplicable Cable (Tin plating Annealed copper wire) Conductor Size (Wire construction) AWG26(7 cores/0.16mm) AWG28(7 cores/0.127mm) AWG30(7 cores/0.1mm) AWG32(7 cores/0.08mm) Jacket Diameter KRecommended Cable UL1571 O0.54 to O1mm KStrip Length 1.2 to 1.9mm Note:If other cables are used instead of the applicable cable, contact Hirose sales department. BApplicable Crimping Tool Type Applicator Press Main Unit Manual Crimping Tool Part Number AP105-DF14-2628S AP105-DF14-3032S CM-105 DF14-2628/CR-HT DF14-3032/CR-HT CL No. 901-4548-1 901-4544-0 901-0005-4 550-0261-1 550-0262-4 Applicable Contact DF14-2628SCF/SCFA DF14-3032SCF/SCFA --------------------------------------------DF14-2628SCF/SCFA DF14-3032SCF/SCFA Note 1.If a trouble has occurred due to tools, which are not designated by Hirose, Hirose won't guarantee any product. Note 2.Use the reel contact sequentially cut for manual crimping tool. B179 sRight Angle Pin Header (SMT) Note 1."Without boss" indicates the style with no boss. BPCB mounting pattern BTube Packaging Dimensions Note 2."Without boss" indicates that no hole is needed. [Specific No.]-**,(**) (20): Tin plated tube packaging (21): Tin plated embossed tape packaging (50): Gold plated tube packaging (59): Gold plated embossed tape packaging Unit: mm With boss Part Number DF14- 2P-1.25H(**) DF14- 3P-1.25H(**) DF14- 4P-1.25H(**) DF14- 5P-1.25H(**) DF14- 6P-1.25H(**) DF14- 7P-1.25H(**) DF14- 8P-1.25H(**) DF14- 9P-1.25H(**) DF14-10P-1.25H(**) DF14-15P-1.25H(**) DF14-20P-1.25H(**) DF14-25P-1.25H(**) DF14-30P-1.25H(**) CL No. Without boss Part Number CL No. Number of Contacts 2 3 4 5 6 7 8 9 10 15 20 25 30 A 7.45 8.70 9.95 11.20 12.45 13.70 14.95 16.20 17.45 23.70 29.95 36.20 42.45 B 1.25 2.50 3.75 5.00 6.25 7.50 8.75 10.00 11.25 17.50 23.75 30.00 36.25 C 6.45 7.70 8.95 10.20 11.45 12.70 13.95 15.20 16.45 22.70 28.95 35.20 41.45 D 8.05 9.30 10.55 11.80 13.05 14.30 15.55 16.80 18.05 24.30 30.55 36.80 43.05 Tube Packaging Quantity 66 56 49 44 39 36 32 30 28 20 16 13 11 538-0021-4-** DF14A- 2P-1.25H(**) 538-0033-3-** 538-0022-7-** DF14A- 3P-1.25H(**) 538-0034-6-** 538-0023-0-** DF14A- 4P-1.25H(**) 538-0035-9-** 538-0024-2-** DF14A- 5P-1.25H(**) 538-0036-1-** 538-0025-5-** DF14A- 6P-1.25H(**) 538-0037-4-** 538-0026-8-** DF14A- 7P-1.25H(**) 538-0038-7-** 538-0027-0-** DF14A- 8P-1.25H(**) 538-0039-0-** 538-0028-3-** DF14A- 9P-1.25H(**) 538-0040-9-** 538-0029-6-** DF14A-10P-1.25H(**) 538-0041-1-** 538-0084-4-** DF14A-15P-1.25H(**) 538-0114-3-** 538-0089-8-** DF14A-20P-1.25H(**) 538-0119-7-** 538-0094-8-** DF14A-25P-1.25H(**) 538-0124-7-** 538-0020-1-** DF14A-30P-1.25H(**) 538-0045-2-** Note 1.Please order the tube packaging product, multiplying the packaging quantity (pcs.). Note 2.Please order the embossed tape packaging product according to reel number. (1000 pcs./reel) B180 BEmbossed Carrier Tape Dimensions s 2 to 10 Contacts s 15, 20, 25, 30 Contacts Unit: mm Inserted Connector DF14/14A- 2P-1.25H DF14/14A- 3P-1.25H DF14/14A- 4P-1.25H DF14/14A- 5P-1.25H DF14/14A- 6P-1.25H DF14/14A- 7P-1.25H DF14/14A- 8P-1.25H DF14/14A- 9P-1.25H DF14/14A-10P-1.25H DF14/14A-15P-1.25H DF14/14A-20P-1.25H DF14/14A-25P-1.25H DF14/14A-30P-1.25H Number of Contacts 2 3 4 5 6 7 8 9 10 15 20 25 30 A 16 16 24 24 24 24 24 24 24 44 44 56 56 B 7.5 7.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 20.2 20.2 26.2 26.2 C 16.4 16.4 24.4 24.4 24.4 24.4 24.4 24.4 24.4 44.4 44.4 56.4 56.4 D -- - -- - -- - -- - -- - -- - -- - -- - -- - 40.4 40.4 52.4 52.4 B181 BPrecautions 1. Recommended Temperature Profile (SMT) Note 1.The soldering process is allowed up to twice under the same condition. However, the interval between the first and second processes must be maintained at the room temperature. Note 1.The temperature indicates the board surface temperature on the connector lead area. 2. Recommended Manual Soldering Condition (SMT) 3. Recommended Screen Thickness (SMT) 4. Board Sled (SMT) 5. Cleaning Condition 6. Connection Condition Manual soldering: 290c for 2 seconds 0.15 to 0.2mm Max 0.03mm at the connector center area, based on both connector edges Refer to Nylon Connector Use Hand book. Refer to Nylon Connector Use Hand book. sBe careful to carry out the crimping operation according to the "Crimping Condition Sheet" and "Crimping Quality Reference", because the crimping contact style is too small. 7. Cautions sBe careful for an excessive scoop insertion/extraction, which will cause damage to the product. B182 |
Price & Availability of DF14-3030SCF |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |